Recalls

Find the latest 2001 Nissan Sentra recalls as issued by the National Highway Traffic Safety Administration (NHTSA) and Manufacturers.

Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.
Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.
Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.
Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.
Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.
Dates of Manufacture February 2000 - June 2001
Dates of Manufacture January 2000 - May 2001
Dates of Manufacture January - October 2001
Dates of Manufacture July 2000 - April 2001
NHTSA CAMPAIGN ID 01V174
NHTSA CAMPAIGN ID 01V277
NHTSA CAMPAIGN ID 01V357
NHTSA CAMPAIGN ID 01V376
Potential Number of Units Affected 103,000
Potential Number of Units Affected 115,000
Potential Number of Units Affected 80,000
Potential Number of Units Affected 81,393
Remedy Dealers will inspect for cracks and replace the wheel if cracks are discovered. The manufacturer has reported that owner notification will be conducted in two phases. The first mailing is expected to begin during October 2001, asking owners to bring their vehicles to a dealer for inspection of the wheels. Any wheels with cracks will be replaced. A second owner notification will begin in early December, at which time Nissan will have an adequate number of replacement wheels, requesting owners who only had the wheels inspected but not replaced, to return to the dealers for a wheel replacement. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will install a tamperproof cap over the horizontal adjustment screw for both headlamps. The manufacturer has reported that owner notification was to begin during January 2002. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the crank position sensors. The manufacturer has reported that owner notification began Dec. 10, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Remedy Dealers will replace the lower control arm attachment bolts. The manufacturer has reported that owner notification began June 25, 2001. Owners who do not receive the free remedy within a reasonable time should contact Nissan at 1-800-647-7261.
Summary Certain passenger vehicles fail to comply with requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment." Vehicles produced during this period were missing tamperproof caps that prevent horizontal headlamp adjustment.
Summary On certain passenger vehicles equipped with 1.8-liter engines, the engine could stop running while being driven due to a defective crank position sensor. This could also result in the "Service Engine Soon" warning light coming on or reduced engine power. If the engine stops running while the vehicle is in motion, it could result in a crash.
Summary On certain passenger vehicles, one or more of the three bolts used to attach each front suspension lower control arm to the body on the left and right sides may not have been properly manufactured and could fracture, increasing the risk of a crash.
Summary On certain passenger vehicles, the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. These burrs can cause cracks as the vehicle is being driven. Cracks can propagate between adjacent cooling holes. If enough cracks develop between the cooling holes, the wheel could fail and separate from the mounting hub without prior warning. Separation of the wheel from the vehicle while being operated could result in a vehicle crash.

Powered by Chrome